Special Notes for Management Adapters Intel PRO/100+ Management Adapter Feature Notes =============================================== Note: the information in this file applies to Intel management adapters only. Standard, non-management adapters do not have a 3-pin auxiliary power connector. 1. Wake on LAN* Description Computer Requirements Settings in Windows* 98 Settings in the computer's BIOS Troubleshooting Wake on LAN 2. Intel(R) PRO/100+ Boot Agent Description Operation Troubleshooting Boot Agent Wake on LAN =========== Description The Wake on LAN (WOL) feature of the PRO/100+ Management adapter allows a WOL-enabled computer to be powered-on remotely by a network management program. In some operating systems, it can also wake the computer from suspend mode. This is accomplished by sending a special type of data packet containing the adapter's specific Ethernet address. The PRO/100+ Management adapter is supplied with a small cable with a 3-pin connector at each end. Some WOL-enabled computers require this cable for the WOL function. In these computers, one end of the cable is attached to the adapter and the other end is attached to the 3-pin WOL connector on the WOL-enabled computer. When the computer is powered off, the adapter continues to operate by using +5 volt standby power through the 3-pin cable in the computer. In WOL-enabled computers that do not require the 3-pin cable, the adapter operates from 3.3 volt standby power supplied through the PCI bus. When the computer is powered off, the adapter continues to operate by using 3.3 volt standby power through the PCI bus. As long as AC power is available to the power supply, the adapter will draw standby power when the machine is powered off, allowing it to "listen" to the network for a wake up packet. NOTE: Early versions of the Management adapter are +5 volt only. These models must have the 3-pin cable attached for the WOL function to work. These adapters can be identified by the fact that they are equipped with 3 LEDs on the adapter bracket, whereas the PCI 2.2 compliant models have 2 LEDs on the adapter bracket. These older, +5 volt model adapters are not compliant to the PCI 2.2 specification and will not fit in a 3-volt only PCI slot. Computer requirements Only a computer designed for Wake on LAN can use the Wake on LAN function. If your computer uses a 3-pin connector for Wake on LAN, make sure the connector matches the 3-pin cable supplied with the PRO/100+ Management adapter. If the computer has a Wake on LAN connector that does not fit the 3-pin cable, do not attempt to use it with this adapter. If your computer requires the 3-pin cable, then the +5 volt standby power supply must be capable of supplying at least 0.2 amps at +5 volts for each PRO/100+ Management adapter installed. This value is usually listed on the power supply label as +5SB, +5VSB or +5AUX. If your WOL-enabled computer is compliant to PCI specification 2.2, then it does not require the 3-pin cable for Wake on LAN. In these computers, the 3.3 volt standby supply must be capable of supplying at least 0.2 amps for each PRO/100+ Management adapter installed. You may need to contact your computer manufacturer to verify the standby current rating. WOL Settings in Microsoft Windows* 98 If the PRO/100+ Management adapter is installed in Microsoft Windows 98, you will have an additional setting in the adapter properties that is not available for other types of PRO/100+ adapters. This setting is titled "ACPI Wake On LAN" and by default is set to "Enabled". You may need to change this setting to "Disabled" if you are using the PRO/100+ Management adapter in a Wake on LAN enabled computer that is not ACPI compliant. Check your computer owner's manual or contact your computer vendor to determine if your computer is ACPI compliant. Settings in the computer's BIOS Many Wake on LAN enabled computers have settings similar to the following: On Modem Ring Stay Off On LAN Power-on On PME Stay Off The setting "On LAN" refers to wake-up events received through the 3-pin WOL connector. The setting "On PME" refers to wake-up events received through a signal on the PCI bus defined as "Power Management Event". The PRO/100+ Management adapter is capable of using either of these methods. Which settings to use will vary with the computer and operating system. The following are suggestions only. In computers running Windows 98, set the "On LAN" BIOS setting to "Stay off" and the "On PME" BIOS setting to "Power-on". In other operating systems set the BIOS setting "On LAN" to "Power-on" and the BIOS setting "On PME" to "Stay Off". B. If these settings do not work for you, try reversing them, or set both to "Power-on". Troubleshooting Wake on LAN Note: The reception of a wake up packet will set the adapter to a special state. This condition must be reset before the adapter will accept another wake up packet and power-on the computer. The drivers for this adapter are written to reset this condition when they load. The only other way of resetting this condition is removing AC power from the computer for a short duration (~10 seconds). Once you have sent the computer a wake up packet and powered-on the computer, you must let a driver load or it will no longer accept any wake up packets. If this happens, you can remove the AC power cord for 10-15 seconds or load an adapter driver to reset the adapter and restore normal operation. If the computer will not power-on when a wake up packet is sent, check the computer's BIOS for power settings (see "Settings in the computer's BIOS" above). If you are connected to a hub or switch, the link LED on the back of the adapter should be on, even though computer power is off. If the link LED it is not on, try powering the computer on. If the LED now lights, then the adapter is not receiving power in standby mode. If this is the case, check to make sure the 3 pin cable is properly plugged into a standard WOL 3 pin connector on systems that require it. Make sure that the power supply is capable of supplying the necessary current (see Computer Requirements above). Also, check with your computer vendor to be sure that the computer is, in fact, capable of supporting Wake on LAN. If the link LED does not come on when the computer is powered-on, you have not established link with your hub or switch. Check your cabling or substitute it with a cable that has been verified to work correctly. Make sure your hub or switch is either 10baseT or 100baseTX and is powered-on and fully functional. If your computer will not power-on at all when the 3-pin cable is attached, but will power-on when the 3-pin cable is removed, your +5 volt standby power supply is possibly insufficient. In systems that do not require the 3-pin cable, this symptom may be caused by an insufficient 3.3 volt standby power supply, especially if you are using multiple PRO/100+ Management adapters (see Computer Requirements above). If everything listed above is correct and the computer will still not respond to a wake up packet, check with your computer vendor for an updated BIOS. Intel(R) PRO/100+ Boot Agent ============================ Description The Boot Agent is a utility program that is stored in a flash memory chip on the adapter, allowing the adapter to remotely boot the system from the network using either of 2 methods. The default method is PXE, a remote boot procedure defined by the "Wired for Management" specifications and used by powerful network management programs, such as Intel(R) LANDesk(R) Management suite. The alternate method is RPL, an established industry standard historically utilized for remote booting of diskless workstations from network operating systems such as NetWare* and Windows NT* Server. Computers do not need to be Wake on LAN enabled to use this feature, and the feature will work with or without the 3-pin auxiliary power connector attached. Configuration When the computer is first powered-on, the Boot Agent will execute and display the following message; Initializing Intel PRO/100 Boot Agent Version 2.0 Press Ctrl+S to enter the Setup Program.. By default, this message will display for 2 seconds, then attempt to boot from a local drive. If the attempt to boot from a local drive fails, the agent will attempt to boot remotely. To change the configuration of the Boot Agent, press the "Ctrl" key and "S" key simultaneously during the time that this message is displayed. This will bring up the Boot Agent configuration screen. There are 5 configurable parameters. Follow the on-screen instructions to select, change and save the different parameters. The different parameters are explained below, with the default parameter listed first. Boot Protocol Selections are PXE and RPL. Select PXE for use with Wired for Management compliant network management programs, such as Intel LANDesk Management Suite. Select RPL for legacy style remote booting. PnP/BEV Boot Selections are Disable and Enable. Select Disable to use the Intel PRO/100+ boot agent for remote boot operation. Select Enable if your computer BIOS has a remote boot program built in and you wish to use that remote boot agent instead of the Intel PRO/100+ Boot Agent. Default Boot Selections are Local and Network. If Local is selected, the Boot Agent will attempt to boot from a local drive first, then attempt to boot from the network if local boot fails. If Network is selected, the Boot Agent will attempt to boot from the network first. Local Boot Selections are Enable and Disable. If Enable is selected, the system will be able to boot from a local drive (floppy drive or hard drive). If disable is selected, the system will not be able to boot from a local drive. This will be true regardless of the Default Boot setting. Prompt Time Selections are 2, 3, 5 and 8. The number represents the amount of time in seconds the "Initializing Intel PRO/100 Boot Agent Version 2.0 - Press Ctrl+S to enter the Setup Program.." message is displayed every time the system is booted. Troubleshooting Boot Agent If you do not see the message " Initializing Intel PRO/100 Boot Agent Version 2.0", check the following; In the computer setup, check for the boot device sequence. If "Intel UNDI, PXE" or "Network" is listed, move it ahead of the hard drive in the boot sequence. Some computers require manual intervention to execute the Boot Agent. Look for an informational note on the computer monitor after power-on that may instruct you on how to execute a network boot. For example, some computers will display the message "F12 Network Service Boot" on the banner screen. When using an RPL remote boot in computers that have a built-in network interface based on an Intel 82557, 82558 or 82559 LAN controller chip, the boot agent may try to remote boot using the built-in interface instead of the PRO/100+ Management adapter. To avoid this, disable the built-in interface in the computer BIOS settings. * Other trademarks and brand names are the property of their owners.