1 Windows NT 3.51 v1.03 Windows NT* 3.51 Installation Notes for the Intel EtherExpress(TM) PRO/100+ PCI LAN Adapter ========================================================================= LOCATION OF DRIVER: \NT\E100B.SY_ (NDIS 3 compressed) \OEMSETUP.INF General instructions -------------------- After putting the adapter in the computer, you need to configure it under Windows NT. 1 Double-click the Network icon in the Control Panel. 2 Click the Add Adapter button. 3 Do NOT select an Intel adapter from the list. Instead, scroll to the end of the list and select: Requires disk from manufacturer. 4 Click the Continue button. 5 Insert the Configuration and Drivers Disk into your floppy drive and click OK. 6 Select "Intel EtherExpress PRO/100+ PCI Adapter (TX or T4)" and click OK. 7 The PROSet Setup utility automatically scans computer resources and determines the settings assigned to your adapter. It also adds an PROSet icon to the Control Panel for future use of PROSet. 8 Click the Test button in the PROSet utility to run diagnostics. If you've just added the adapter, the network driver won't be active and the diagnostics will test the adapter and its connection to the network. If you're testing an adapter that's already been installed, the network driver will probably be active and the diagnostics will test the driver. This diagnostic tracks the driver's actual network activity. 9 Click OK to exit the test screen and return to the PROSet main menu. 10 Click OK to accept the adapter's configuration and exit PROSet. 11 Click OK in the Network Settings dialog. Other configuration screens may appear. Configure as desired. When prompted, restart Windows NT. Note: The NDIS 3 miniport driver will automatically get installed in Windows NT 3.51. 12 Repeat the these steps for installing additional adapters. Adapter settings ---------------- There are two ways to run PROSet, which allows changing the adapter settings. - From the Control Panel double click the PROSet icon. - From the Network Settings screen highlight the PRO/100+ adapter and click Configure. From the main PROSet menu click the Change button to get to the Adapter Settings screen. The defaults work correctly for most configurations. Network speed ------------- Recommended setting: Auto (default) This parameter lets the PRO/100+ adapter know what speed to use on the Ethernet wire. The choices are 10 Mbps, 100 Mbps, and Auto. In Auto mode, the adapter detects if its environment can support 100 Mbps speed. It then sets the speed to 100 if it can, or 10 if it can't. If you are using a crossover cable connected to another adapter, set the speed to either 10 Mbps or 100 Mbps. Note: If the Duplex Mode is not set to Auto, then set the speed to either 10 Mbps or 100 Mbps. Duplex mode ----------- Recommended setting: Auto (PRO/100+ TX adapter only) Auto: The adapter negotiates with the hub how to send/receive packets, either full or half duplex. Full duplex: The adapter sends and receives packets at the same time. This improves the performance of your adapter. Set duplex mode to full duplex only if you have a full duplex switch. Half duplex: The adapter performs one operation at a time. It either sends or receives. A regular adapter can perform only one operation at a time (half- duplexing). The PRO/100+ adapter has the ability to send and receive packets at the same time (full-duplexing) at both 10 and 100 Mbps. In order to reap the benefits of full duplexing, you MUST have a full duplex switch or hub. The PRO/100+ adapter has the added ability to "talk" to the switch or hub and determine at which mode to communicate (either full or half duplex). This is called auto-negotiation. You must have an auto-negotiating switch to get full duplex support with the Duplex Mode set to Auto. If you don't have an auto-negotiating switch or hub and want to run at full duplex, set Duplex Mode to Full and then set the SPEED parameter to either 100 Mbps or 10 Mbps. Note: If you set duplex to Full, and leave Speed at Auto, the adapter will run at 10 Mbps. 2 Click the Advanced button in the Adapter Settings screen to change the advanced settings. Note: The defaults work correctly for most configurations. Please use caution when changing these parameters. Use the online help for additional information. Coalesce buffers ---------------- Recommended setting: 8 Receive buffers --------------- Recommended setting: 16 Transmit control blocks ----------------------- Recommended setting: 16 Adaptive transmit threshold --------------------------- Recommended setting: On This parameter dynamically optimizes the point at which early transmit cycles will be executed. This results in higher performance but may generate an occasional underrun. To eliminate underruns, set it to OFF. Adaptive Technology ------------------- Recommended setting: On Adaptive Technology customizes the PRO/100+ adapter to the respective operating system by downloading microcode to the silicon. This improves performance and minimizes CPU utilization. Map registers ------------- Recommended settings: PCI: MapRegisters = 8 (default for NT 3.5) PCI: MapRegisters = 64 (default for NT 3.51 or later) * Third-party trademarks are the property of their respective owners.